 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Order this document by MC33078/D MC33078 MC33079 Dual/Quad Low Noise Operational Amplifiers The MC33078/9 series is a family of high quality monolithic amplifiers employing Bipolar technology with innovative high performance concepts for quality audio and data signal processing applications. This family incorporates the use of high frequency PNP input transistors to produce amplifiers exhibiting low input voltage noise with high gain bandwidth product and slew rate. The all NPN output stage exhibits no deadband crossover distortion, large output voltage swing, excellent phase and gain margins, low open loop high frequency output impedance and symmetrical source and sink AC frequency performance. The MC33078/9 family offers both dual and quad amplifier versions, tested over the automotive temperature range and available in the plastic DIP and SOIC packages (P and D suffixes). * Dual Supply Operation: 5.0 V to 18 V DUAL/QUAD LOW NOISE OPERATIONAL AMPLIFIERS DUAL 8 1 1 8 P SUFFIX PLASTIC PACKAGE CASE 626 * * * * * * * * * * D SUFFIX PLASTIC PACKAGE CASE 751 (SO-8) Low Voltage Noise: 4.5 nV/ Hz Low Input Offset Voltage: 0.15 mV Low T.C. of Input Offset Voltage: 2.0 V/C Low Total Harmonic Distortion: 0.002% High Gain Bandwidth Product: 16 MHz High Slew Rate: 7.0 V/s High Open Loop AC Gain: 800 @ 20 kHz Excellent Frequency Stability Large Output Voltage Swing: +14.1 V/ -14.6 V ESD Diodes Provided on the Inputs PIN CONNECTIONS Output 1 1 2 Inputs 1 3 4 - 1 + - 2 + (Dual, Top View) QUAD 8 VCC 7 Output 2 6 Inputs 2 5 VEE 14 1 14 1 Representative Schematic Diagram (Each Amplifier) VCC D1 R2 Q4 Q3 Neg J1 Amplifier Biasing Q6 Q2 Z1 Q1 R1 C1 R3 D2 R4 Q7 Q10 R6 Q5 VEE Q12 Q5 Pos D3 C2 Q8 Q9 Q11 R7 Q3 D4 C3 R9 Vout P SUFFIX PLASTIC PACKAGE CASE 646 D SUFFIX PLASTIC PACKAGE CASE 751A (SO-14) PIN CONNECTIONS Output 1 Inputs 1 VCC Inputs 2 Output 2 1 2 3 4 5 6 7 14 *1 ) )2 * 4 * ) 12 13 11 Output 4 Inputs 4 VEE Inputs 3 Output 3 ) 10 3 *9 8 (Quad, Top View) ORDERING INFORMATION Device MC33078D MC33078P MC33079D MC33079P Operating Temperature Range Package SO-8 Plastic DIP SO-14 Plastic DIP Rev 0 TA = - 40 to +85C (c) Motorola, Inc. 1996 MOTOROLA ANALOG IC DEVICE DATA 1 MC33078 MC33079 MAXIMUM RATINGS Rating Supply Voltage (VCC to VEE) Input Differential Voltage Range Input Voltage Range Output Short Circuit Duration (Note 2) Maximum Junction Temperature Storage Temperature Maximum Power Dissipation Symbol VS VIDR VIR tSC TJ Tstg PD Value +36 (Note 1) (Note 1) Indefinite +150 - 60 to +150 (Note 2) Unit V V V sec C C mW NOTES: 1. Either or both input voltages must not exceed the magnitude of VCC or VEE. 2. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded (see Figure 1). DC ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = -15 V, TA = 25C, unless otherwise noted.) Characteristics Input Offset Voltage (RS = 10 , VCM = 0 V, VO = 0 V) (MC33078) TA = +25C TA = -40 to +85C (MC33079) TA = +25C TA = -40 to +85C Average Temperature Coefficient of Input Offset Voltage RS = 10 , VCM = 0 V, VO = 0 V, TA = Tlow to Thigh Input Bias Current (VCM = 0 V, VO = 0 V) TA = +25C TA = -40 to +85C Input Offset Current (VCM = 0 V, VO = 0 V) TA = +25C TA = -40 to +85C Common Mode Input Voltage Range (VIO = 5.0 mV, VO = 0 V) Large Signal Voltage Gain (VO = 10 V, RL = 2.0 k) TA = +25C TA = -40 to +85C Output Voltage Swing (VID = 1.0V) RL = 600 RL = 600 RL = 2.0 k RL = 2.0 k RL = 10 k RL = 10 k Common Mode Rejection (Vin = 13V) Power Supply Rejection (Note 3) VCC/VEE = +15 V/ -15 V to +5.0 V/ -5.0 V Output Short Circuit Current (VID = 1.0 V, Output to Ground) Source Sink Power Supply Current (VO = 0 V, All Amplifiers) (MC33078) TA = +25C (MC33078) TA = -40 to +85C (MC33079) TA = +25C (MC33079) TA = -40 to +85C NOTE: 3. Measured with VCC and VEE differentially varied simultaneously. Symbol |VIO| Min -- -- -- -- Typ 0.15 -- 0.15 -- 2.0 Max 2.0 3.0 2.5 3.5 -- Unit mV VIO/T IIB -- V/C nA -- -- IIO -- -- VICR AVOL 90 85 VO + VO - VO + VO - VO + VO - CMR PSR ISC +15 -20 ID -- -- -- -- -- -- +13.2 -- +13.5 -- 80 80 13 300 -- 25 -- 14 110 -- +10.7 -11.9 +13.8 -13.7 +14.1 -14.6 100 105 750 800 nA 150 175 -- -- -- V -- -- -- -13.2 -- -14 -- -- dB dB mA V dB +29 -37 4.1 -- 8.4 -- -- -- mA 5.0 5.5 10 11 2 MOTOROLA ANALOG IC DEVICE DATA MC33078 MC33079 AC ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = -15 V, TA = 25C, unless otherwise noted.) Characteristics Slew Rate (Vin = -10 V to +10 V, RL = 2.0 k, CL = 100 pF AV = +1.0) Gain Bandwidth Product (f = 100 kHz) Unity Gain Frequency (Open Loop) Gain Margin (RL = 2.0 k) Phase Margin (RL = 2.0 k) Channel Separation (f = 20 Hz to 20 kHz) Power Bandwidth (VO = 27 Vpp, RL = 2.0 k, THD 1.0%) Distortion (RL = 2.0 k, f = 20 Hz to 20 kHz, VO = 3.0 Vrms, AV = +1.0) Open Loop Output Impedance (VO = 0 V, f = 9.0 MHz) Differential Input Resistance (VCM = 0 V) Differential Input Capacitance (VCM = 0 V) Equivalent Input Noise Voltage (RS = 100 , f = 1.0 kHz) Equivalent Input Noise Current (f = 1.0 kHz) CL = 0 pF CL = 100 pF CL = 0 pF CL = 100 pF Symbol SR GBW fU Am m CS BWp THD |ZO| RIN CIN en in Min 5.0 10 -- -- -- -- -- -- -- -- -- -- -- -- -- Typ 7.0 16 9.0 -11 - 6.0 55 40 -120 120 0.002 37 175 12 4.5 0.5 Max -- -- -- -- -- -- -- -- -- -- -- -- -- Unit V/s MHz MHz dB Degree s dB kHz % k pF nV/ Hz pA/ Hz Figure 1. Maximum Power Dissipation versus Temperature P D , MAXIMUM POWER DISSIPATION (mW) 2400 MC33078P & MC33079P I IB , INPUT BIAS CURRENT (nA) 800 Figure 2. Input Bias Current versus Supply Voltage VCM = 0 V TA = 25C 600 2000 1600 MC33079D 1200 800 400 0 -55 -40 -20 MC33078D 400 200 0 20 40 60 80 100 120 140 160 TA, AMBIENT TEMPERATURE (C) 0 5.0 10 15 VCC, | VEE |, SUPPLY VOLTAGE (V) 20 Figure 3. Input Bias Current versus Temperature 1000 V IO, INPUT OFFSET VOLTAGE (mV) I IB , INPUT BIAS CURRENT (nA) 800 600 400 VCC = +15 V VEE = -15 V VCM = 0 V Figure 4. Input Offset Voltage versus Temperature 2.0 VCC = +15 V VEE = -15 V RS = 10 1.0 VCM = 0 V AV = +1 0 Unit 3 Unit 1 Unit 2 200 0 -55 -1.0 -25 0 25 50 75 TA, AMBIENT TEMPERATURE (C) 100 125 -2.0 -55 -25 0 25 50 75 TA, AMBIENT TEMPERATURE (C) 100 125 MOTOROLA ANALOG IC DEVICE DATA 3 MC33078 MC33079 Figure 5. Input Bias Current versus Common Mode Voltage 600 I IB, INPUT BIAS CURRENT (nA) 500 400 300 200 100 0 -15 VCC = +15 V VEE = -15 V TA = 25C V ICR , INPUT COMMON MODE VOLTAGE RANGE (V) Figure 6. Input Common Mode Voltage Range versus Temperature VCC -0 VCC -0.5 VCC -1.0 VCC -1.5 Voltage Range VEE +1.5 VEE +1.0 VEE +0.5 VEE +0 - 55 -VCM +VCM VCC = +3.0 V to +15 V VEE = -3.0 V to -15 V VIO = 5.0 mV VO = 0 V -10 - 5.0 0 5.0 10 15 - 25 0 25 50 75 100 125 VCM, COMMON MODE VOLTAGE (V) TA, AMBIENT TEMPERATURE (C) Figure 7. Output Saturation Voltage versus Load Resistance to Ground | I SC |, OUTPUT SHORT CIRCUIT CURRENT (mA) 50 Vsat , OUTPUT SATURATION VOLTAGE (V) VCC -1.0 VCC -3.0 VCC -5.0 -55C 25C 125C 125C 25C -55C 0 1.0 2.0 3.0 4.0 Figure 8. Output Short Circuit Current versus Temperature VCC = +15 V VEE = -15 V RL < 100 VID = 1.0 V VCC = +15 V VEE = -15 V Sink 40 Source 30 VEE +5.0 VEE +3.0 VEE +1.0 20 10 - 55 - 25 0 25 50 75 100 125 RL, LOAD RESISTANCE TO GROUND (k) TA, AMBIENT TEMPERATURE (C) Figure 9. Supply Current versus Temperature VCM = 0 V RL = VO = 0 V CMR, COMMON MODE REJECTION (dB) 10 I CC , SUPPLY CURRENT (mA) 8.0 6.0 4.0 2.0 0 - 55 15 V 5.0 V Supply Voltages 10 V 15 V 5.0 V 10 V 160 140 120 100 80 60 40 20 100 Figure 10. Common Mode Rejection versus Frequency VCM - ADM + VCM VO x ADM VO CMR = 20Log MC33079 MC33078 VCC = +15 V VEE = -15 V VCM = 0 V VCM = 1.5 V TA = 25C 1.0 k 10 k 100 k f, FREQUENCY (Hz) 1.0 M 10 M - 25 0 25 50 75 TA, AMBIENT TEMPERATURE (C) 100 125 4 MOTOROLA ANALOG IC DEVICE DATA MC33078 MC33079 Figure 11. Power Supply Rejection versus Frequency +PSR = 20Log VCC -PSR = 20Log Figure 12. Gain Bandwidth Product versus Supply Voltage GWB, GAIN BANDWIDTH PRODUCT (MHz) 30 RL = 10 k CL = 0 pF f = 100 kHz TA = 25C 140 PSR, POWER SUPPLY REJECTION (dB) 120 100 80 60 40 20 VCC = +15 V VEE = -15 V TA = 25C 1.0 k VO/ADM VO/ADM VCC VCC - ADM + VO VEE +PSR 20 -PSR 10 0 100 0 5.0 10 15 20 VCC |VEE| , SUPPLY VOLTAGE (V) 10 k 100 k f, FREQUENCY (Hz) 1.0 M 10 M Figure 13. Gain Bandwidth Product versus Temperature GWB, GAIN BANDWIDTH PRODUCT (MHz) 20 VO , OUTPUT VOLTAGE (Vp) 20 15 15 10 5.0 0 -5.0 -10 -15 25 50 75 100 125 -20 5.0 Figure 14. Maximum Output Voltage versus Supply Voltage TA = 25C RL = 10 k RL = 2.0 k VO + 10 VCC = +15 V VEE = -15 V f = 100 kHz RL = 10 k CL = 0 pF -25 0 5.0 RL = 2.0 k RL = 10 k 10 15 VO - 20 0 -55 TA, AMBIENT TEMPERATURE (C) VCC |VEE| , SUPPLY VOLTAGE (V) Figure 15. Output Voltage versus Frequency A VOL, OPEN LOOP VOLTAGE GAIN (dB) 35 VO, OUTPUT VOLTAGE (Vpp ) 30 25 20 15 10 5.0 0 10 VCC = +15 V VCC = -15 V RL = 2.0 k AV = +1.0 THD 1.0% TA = 25C 100 1.0 k 10 k 100 k f, FREQUENCY (Hz) 1.0 M 10 M 110 Figure 16. Open Loop Voltage Gain versus Supply Voltage RL = 2.0 k f 10 Hz VO = 2/3 (VCC -VEE) TA = 25C 100 90 80 5.0 10 15 VCC |VEE| , SUPPLY VOLTAGE (V) 20 MOTOROLA ANALOG IC DEVICE DATA 5 MC33078 MC33079 Figure 17. Open Loop Voltage Gain versus Temperature A VOL, OPEN LOOP VOLTAGE GAIN (dB) 110 | Z O |, OUTPUT IMPEDANCE ( ) VCC = +15 V VEE = -15 V RL = 2.0 k f 10 Hz VO = -10 V to +10 V 50 40 VCC = +15 V VEE = -15 V VO = 0 V TA = 25C Figure 18. Output Impedance versus Frequency 105 30 20 10 0 1.0 k AV = 1000 100 95 AV = 100 100 k AV = 10 1.0 M AV = 1.0 10 M 90 -55 -25 0 25 50 75 100 125 10 k TA, AMBIENT TEMPERATURE (C) f, FREQUENCY (Hz) Figure 19. Channel Separation versus Frequency CS, CHANNEL SEPARATION (dB) MC33078 150 140 130 120 110 100 10 100 10 k - + 100 Measurement Channel VOM Figure 20. Total Harmonic Distortion versus Frequency THD, TOTAL HARMONIC DISTORTION (%) 1.0 VCC = +15 V VEE = -15 V VO = 1.0 Vrms TA = 25C - + VO 2.0 k 160 MC33079 Drive Channel VCC = +15 V VEE = -15 V RL = 2.0 K VOD = 20 Vpp TA = 25C 0.1 0.01 CS = 20 Log 10 k VOA VOM 100 k 0.001 10 100 1.0 k f, FREQUENCY (Hz) 10 k 100 k 100 1.0 k f, FREQUENCY (Hz) Figure 21. Total Harmonic Distortion versus Output Voltage THD, TOTAL HARMONIC DISTORTION (%) 1.0 VCC = +15 V VEE = -15 V 0.5 f = 2.0 kHz TA = 25C 0.1 0.05 0.01 0.005 0.001 AV = 10 AV = 1.0 10 AV = 1000 AV = 100 RA Vin - + 10 k VO 2.0 k Figure 22. Slew Rate versus Supply Voltage Vin = 2/3 (VCC -VEE) TA = 25C Falling Rising SR, SLEW RATE (V/ s) 8.0 6.0 4.0 2.0 0 5.0 - Vin + VO 2.0 k 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 VO, OUTPUT VOLTAGE (Vrms) 8.0 9.0 10 15 VCC |VEE| , SUPPLY VOLTAGE (V) 20 6 MOTOROLA ANALOG IC DEVICE DATA MC33078 MC33079 Figure 23. Slew Rate versus Temperature VCC = +15 V VEE = -15 V Vin = 20 V Falling Rising 6.0 - VO 2.0 k Figure 24. Voltage Gain and Phase versus Frequency A VOL , OPEN LOOP VOLTAGE GAIN (dB) 120 100 80 60 Gain 40 135 20 0 1.0 180 10 M VCC = +15 V VEE = -15 V RL = 2.0 k TA = 25C 0 , EXCESS PHASE (DEGREES) 10 SR, SLEW RATE (V/ s) 8.0 45 Phase 90 4.0 Vin + 2.0 -55 -25 0 25 50 75 TA, AMBIENT TEMPERATURE (C) 100 125 10 100 1.0 k 10 k 100 k f, FREQUENCY (Hz) 1.0 M Figure 25. Open Loop Gain Margin and Phase Margin versus Load Capacitance 14 A m , OPEN LOOP GAIN MARGIN (dB) - Figure 26. Overshoot versus Output Load Capacitance 0 100 m, PHASE MARGIN (DEGREES) - 12 Vin 10 8.0 -55C 125C 20 30 os, OVERSHOOT (%) + 2.0 k VO CL 125C VO CL 10 25C Phase 80 60 40 20 0 10 Vin + 25C - 55C 6.0 4.0 2.0 0 1 VCC = +15 V VEE = -15 V VO = 0 V 10 125C 40 50 25C -55C Gain 100 60 70 1000 VCC = +15 V VEE = -15 V Vin = 100 mV 100 1.0 k 10 k CL, OUTPUT LOAD CAPACITANCE (pF) CL, OUTPUT LOAD CAPACITANCE (pF) e n , INPUT REFERRED NOISE VOLTAGE ( nV/ Hz ) i n, INPUT REFERRED NOISE CURRENT ( pA/ Hz ) Figure 27. Input Referred Noise Voltage and Current versus Frequency 100 80 50 30 20 10 8.0 5.0 3.0 2.0 1.0 10 Voltage 10 VCC = +15 V VEE = -15 V TA = 25C Figure 28. Total Input Referred Noise Voltage versus Source Resistance Vn, REFERRED NOISE VOLTAGE (nV/ Hz) 1000 VCC = +15 V VEE = -15 V f = 1.0 kHz TA = 25C Vn(total) = (inRs)2 100 ) en2 ) 4KTRS 10 Current 100 1.0 k f, FREQUENCY (Hz) 10 k 0.1 100 k 1.0 10 100 1.0 k 10 k 100 k 1.0 M RS, SOURCE RESISTANCE () MOTOROLA ANALOG IC DEVICE DATA 7 MC33078 MC33079 Figure 29. Phase Margin and Gain Margin versus Differential Source Resistance 14 12 Am, GAIN MARGIN (dB) 10 R1 70 Gain Phase - + VO 60 50 40 30 20 10 8.0 6.0 4.0 2.0 0 R2 VCC = +15 V VEE = -15 V RT = R1 +R2 AV = +100 VO = 0 V TA = 25C 10 100 1.0 k 10 k RT, DIFFERENTIAL SOURCE RESISTANCE () 0 100 k Figure 30. Inverting Amplifier Slew Rate V O , OUTPUT VOLTAGE (5.0 V/DIV) VCC = +15 V VEE = -15 V AV = -1.0 RL = 2.0 k CL = 100 pF TA = 25C V O , OUTPUT VOLTAGE (5.0 V/DIV) Figure 31. Noninverting Amplifier Slew Rate VCC = +15 V VEE = -15 V AV = +1.0 RL = 2.0 k CL = 100 pF TA = 25C t, TIME (2.0 s/DIV) Figure 32. Noninverting Amplifier Overshoot e n , INPUT NOISE VOLTAGE (100 nV/DIV) V O , OUTPUT VOLTAGE (5.0 V/DIV) VCC = +15 V VEE = -15 V RL = 2.0 k CL = 100 pF AV = +1.0 TA = 25C Figure 33. Low Frequency Noise Voltage versus Time VCC = +15 V VEE = -15 V BW = 0.1 Hz to 10 Hz TA = 25C t, TIME (200 s/DIV) 8 MOTOROLA ANALOG IC DEVICE DATA m , PHASE MARGIN (DEGREES) t, TIME (2.0 s/DIV) t, TIME (1.0 sec/DIV) MC33078 MC33079 Figure 34. Voltage Noise Test Circuit (0.1 Hz to 10 Hzp-p) 0.1 F 10 100 k - 2.0 k D.U.T. + 4.7 F + 1/2 4.3 k 22 F Scope x1 Rin = 1.0 M MC33078 - 100 k 2.2 F 24.3 k 0.1 F Voltage Gain = 50,000 110 k Note: All capacitors are non-polarized. MOTOROLA ANALOG IC DEVICE DATA 9 MC33078 MC33079 OUTLINE DIMENSIONS P SUFFIX PLASTIC PACKAGE CASE 626-05 ISSUE K 8 5 -B- 1 4 F NOTE 2 NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC --- 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC --- 10_ 0.030 0.040 -A- L C -T- SEATING PLANE J N D K M M H G 0.13 (0.005) TA M B M D SUFFIX PLASTIC PACKAGE CASE 751-05 (SO-8) ISSUE R A 8 D 5 C E 1 4 H 0.25 M B M h B C e A SEATING PLANE X 45 _ NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETERS. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.18 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ q L 0.10 A1 0.25 B M CB S A S q 10 MOTOROLA ANALOG IC DEVICE DATA MC33078 MC33079 OUTLINE DIMENSIONS P SUFFIX PLASTIC PACKAGE CASE 646-06 ISSUE L NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01 14 8 B 1 7 A F C N H G D SEATING PLANE L J K M D SUFFIX PLASTIC PACKAGE CASE 751A-03 (SO-14) ISSUE F -A- 14 8 -B- 1 7 P 7 PL 0.25 (0.010) M B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. G C R X 45 _ F -T- SEATING PLANE D 14 PL 0.25 (0.010) M K TB S M A S J DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 MOTOROLA ANALOG IC DEVICE DATA 11 MC33078 MC33079 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 12 *MC33078/D* MOTOROLA ANALOG IC DEVICE DATA MC33078/D |
Price & Availability of MC33078
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |